Pistolsmith

Go Back   Pistolsmith > Revolver Forum > Revolvers


Reply
 
LinkBack Thread Tools Display Modes
Old 11-30-2011, 12:30 PM   #1
Member
 
Aguila Blanca's Avatar
 
Join Date: Feb 2006
Posts: 42
Taurus frames sizes & grips?

I recently purchased (new) a Taurus Model 94 DA .22LR revolver for use in Basic Handgun classes. These guns come from the factory with round-butt, "carry" grips. Since I have no intention of carrying it, I would prefer to mount square butt grips, if I can find some that aren't expensive. But ... I don't know what other models (if any) share the same frame, so I don't know what will fit.

The gun as shipped looks like this:


I'd like to find some grips that will convert it to something more like this:


Material isn't important. I love wood, but rubber or plastic would be acceptable. I'm more interested in just getting the square butt shape. And price IS an object -- I am retired and I can't justify (even to myself, let alone to SWMBO) spending almost as much on a pair of grips as the gun cost.

So:

1. What other Tauri share the same frame?

2. Who has grips for it/them?

Thanks
 
Remove Ads
Old 11-30-2011, 09:24 PM   #2
Senior Member
 
Join Date: May 2006
Location: Huntsville, Ala.
Posts: 534
IIRC, the smaller Taurus revolver frames have all been either round butt or a newer style where there is just a spring housing projecting down into a grip.

If the grips on yours are held with a screw from the side, you will probably have to fit a pair like you want (maybe S&W) with plastic wood or similar.

If yours are held with a screw from the bottom, you will need to do similar but more difficult in that you will have to figure out how to mount them.
 
Old 12-02-2011, 12:59 PM   #3
Member
 
Aguila Blanca's Avatar
 
Join Date: Feb 2006
Posts: 42
It's a round butt frame, not unlike this:



How close are Taurus small frames to S&W -- and which S&W? I don't mind doing a bit of minor carving or filling with plastic wood, but I'm not skilled enough with wood to basically do a custom makeover.
 
Old 12-03-2011, 03:23 AM   #4
Senior Member
 
Join Date: May 2006
Location: Huntsville, Ala.
Posts: 534
Surprised me there is an aftermarket version:
Fancy Hardwood Grips Taurus Small Frame Goncalo Alves

To answer your question, the S&W J frames (Models 36, 37, 38, 60, 34, etc) are closest to your frame. I got ahold of small frame Taurus like yours and some square butt J frame grips to check. You will have to drill new stud holes as yours are toward the front and the S&W's are in the middle. You will also need to apply some filler but not as much as for K/L frame square butt grips (K Models 10, 12, 13, 17, 18, 19, 64, 67, 66, etc. L Models 581, 586, 681, 686).

I mention the K/L frames because used grips for them may be easier/cheaper to get. You could even use N frame grips, but that requires more filler.

In either case be sure to avoid the thin "service" grips because you've indicated you don't want those. Also keep in mind you want to avoid round butt grips for any of those frames unless you happen to run into a pair made for round butt J frames with an outside square butt configuration. Pachmayr used to make some rubber grips like that and they still make some with finger grooves.
 
Old 12-03-2011, 06:30 PM   #5
Member
 
Aguila Blanca's Avatar
 
Join Date: Feb 2006
Posts: 42
Thank you, Sir
 
Old 12-05-2011, 01:46 AM   #6
Senior Member
 
Join Date: May 2006
Location: Huntsville, Ala.
Posts: 534
Remember if you use a filler such as bedding compound or epoxy, you will need a release agent on the frame before applying the filler. Brownells sells both Acraglas and release agent. Keep in mind some fillers such as Acraglas may migrate while you're waiting for it to cure with a grip on frame. Don't skimp on release agent coverage.

If you're really being economical, at least four coats of paste wax everwhere on the frame the filler might touch or migrate to, should suffice. Buff well EACH coat before the next.
 
Old 06-20-2012, 09:02 PM   #7
Junior Member
 
Join Date: Jun 2012
Location: usa
Posts: 7
where did you get it? looking great. I'm looking for one
 
Reply

  Pistolsmith > Revolver Forum > Revolvers


Search tags for this page
rubber grips for taurus 94
,

taurus 94 grips

,

taurus 94 wood grips

,
taurus model 94 22lr grips
,

taurus small frame revolver grips

,

taurus small frame wood grips

,
wood grips for taurus 66
,

wood grips for taurus model 94

,

wood grips for taurus revolvers


Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
EAA Witness Frame Sizes? GroesseBaer Gun Talk 1 03-01-2005 10:31 PM
1911 Colt Sizes The Shootist Colt Pistols 3 10-23-2003 04:04 PM
Lead vs. Steel Shot Sizes... Drew78 Shotguns 1 04-16-2003 02:29 PM
ammo sizes explanation Ballistic_217 Ammunition 1 02-11-2003 03:15 PM
Taurus Grips CCFPS Revolvers 4 01-14-2003 05:14 PM

Top Gun Sites Top Sites List


Powered by vBulletin 3.8.7
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.1
Copyright © 1999-2012 Pistolsmith. All rights reserved.